T3 1.8t conversion build thread |
Post Reply | Page <12345 8> |
Author | |
Sid1800
Groupie Joined: 07 Oct 12 Location: Bradford Status: Offline Points: 70 |
Post Options
Thanks(0)
|
Hello al
I will get some pictures up shortly for the diesel conversion. I am doing both vehicles at the same time just waiting on some Parts at the moment. It looks like if you already have diesel the Conversion is much easier if going to tdi petrol takes some fabrication Parts to be made. But I have made it fit under the hood which is the main Objective . Any idea on your svx engine what went wrong with it, is it worth saving. |
|
S-Line Motors-Photobucket
German Vehicle Specialist 07971728333 |
|
Dyno Soar
Groupie Joined: 13 Apr 05 Location: London, England Status: Offline Points: 162 |
Post Options
Thanks(0)
|
Its coil packs most likely.
Just a bit of a bugger really...
|
|
Sid1800
Groupie Joined: 07 Oct 12 Location: Bradford Status: Offline Points: 70 |
Post Options
Thanks(0)
|
why dont you flash the ecu to see what code comes up it should come up with coil pack problems.on mine
still having problems with rev counter got it to work with taking signal from ignition amplifier,but not accurate as i rev the powersteering kicks on but on idle no powersteering. my vehicle revs faster than the needle moves,at the moment dont know what to do. there must be someone out there who can give me some advice on what to do.
|
|
S-Line Motors-Photobucket
German Vehicle Specialist 07971728333 |
|
Sid1800
Groupie Joined: 07 Oct 12 Location: Bradford Status: Offline Points: 70 |
Post Options
Thanks(0)
|
at last my t3/20vt is up and running.
got the rev counter and powersteering up and running. so far have drove it 100 miles local driving and had no issues at the moment, at 50 mph the revs were sat at 2000rpm and cruising along. will get some pictures up soon of the rest of the conversion and it driving. also waiting on ecu for chris van so i can test drive the 50 degree diesel install which i carried out aswell. |
|
S-Line Motors-Photobucket
German Vehicle Specialist 07971728333 |
|
ELVIS
Moderator Group Silence is golden, gaffa tape is silver Joined: 04 Nov 06 Location: Promised Land Status: Offline Points: 9982 |
Post Options
Thanks(0)
|
nice one sid!
deffo piccies and an in depth build thread!
|
|
Www.justgiving.com/ELVIS-SUMMERS
|
|
Dyno Soar
Groupie Joined: 13 Apr 05 Location: London, England Status: Offline Points: 162 |
Post Options
Thanks(0)
|
Congratulations mate!
Thats some going using the prototype parts. Hopefully this solution will ensure our wagens have a modern alternative drivetrain. I am really keen to see how Chris's Tdi conversion turns out. Any thoughts of performance chip upgrades at this point? How does the 150bhp feel verses the 112bhp from the 2.1?
|
|
Sid1800
Groupie Joined: 07 Oct 12 Location: Bradford Status: Offline Points: 70 |
Post Options
Thanks(0)
|
Hello
Alam happy new year. You saying the difference, well the 2.1 on original Box was good reving but the 20vt is more refined as to How you drive it. The turbo is more like a supercharger Long in gears 2nd gear easy 45. As for upgrade bigger turbo, Injectors,and a remap should be easy 200bhp, As you know I have had 230bhp in same vehicle And I do drive it! |
|
S-Line Motors-Photobucket
German Vehicle Specialist 07971728333 |
|
Arc Eye
Groupie Joined: 01 Dec 04 Status: Offline Points: 96 |
Post Options
Thanks(0)
|
Hi there, great conversion youve done there
What gearbox are you using for this as you say its an Audi and all you did was turn it upside down, no internal mods at all???
Awesome stuff there
|
|
When all else fails, read the instructions.
|
|
VW Nerd
Yardie Joined: 20 Jan 08 Location: Bristol Status: Offline Points: 831 |
Post Options
Thanks(0)
|
Hi Arc Eye check out my build thread for more details about what is involved in the gearbox install. http://www.brick-yard.co.uk/forum/audi-a4-passat-gear-box-install_topic71714.html Tim
|
|
Developing parts for the VW T3 TDI market Inc flipped audi gearbox install parts.
Tim Shettle www.ultimate-engineering.co.uk Bristol Tel/txt 07810 320 464 AFN TDI Panel Van |
|
Dyno Soar
Groupie Joined: 13 Apr 05 Location: London, England Status: Offline Points: 162 |
Post Options
Thanks(0)
|
Sid did the Diesel conversion is done too... my mate Chris should soon be picking up his camper with VW Passat TDi engine and gearbox (all from the same donar Passat) from Sid this or next week.
Sid has promised a test drive in his Turbo Caravelle with Audi engine and Box back to back with the Diesel conversion. Lets see how they compare. I'm hoping tag along and get a test drive myself. I'll do a video and post them upf for everyone to have a looksee. :)
|
|
Racebiz
Groupie Joined: 29 Mar 11 Location: S E Cornwall Status: Offline Points: 95 |
Post Options
Thanks(0)
|
Should make for a couple of interesting test drives.
Up to a few months ago I was all set on dropping an AFN in with a flipped box, however leaving any fuel savings out of the equation for the diesel I am quite keen on the 1.8t as an alternative so will be reading your comparison with interest. |
|
98 T3 PD130 Viking Top
A4 1.9 TDI Classic RangeRover 3.9 EFI |
|
Arc Eye
Groupie Joined: 01 Dec 04 Status: Offline Points: 96 |
Post Options
Thanks(0)
|
Just read the thread, really excellent
|
|
When all else fails, read the instructions.
|
|
Sid1800
Groupie Joined: 07 Oct 12 Location: Bradford Status: Offline Points: 70 |
Post Options
Thanks(0)
|
hi im looking to do the same conversion with a upright diesel so every thing from an audi or passat will fit need to do it with the entire engine sitting under the hood which should not be a problem. the only issue is that i dont have any t3 left to do the conversion in so if any body out there whants it installing give me a shout.ill be more than happy to do it.or for that matter even 1.8t. does anybody know of someone who can do the wiring loom for the 1.9pd engine that will be the diesel conversion to go for.
Edited by Sid1800 - 09 Jan 13 at 20:13 |
|
S-Line Motors-Photobucket
German Vehicle Specialist 07971728333 |
|
rhysdubber
Groupie Joined: 10 Jan 13 Location: South Wales Status: Offline Points: 41 |
Post Options
Thanks(0)
|
I'd very much like to know how you would go about it with a upright Diesel engine and I would crap myself if my van could do what yours done! haha
|
|
If my calculations are correct, when this baby hits eighty-eight miles per hour... you're gonna see some serious shit.
"Better To Be Pissed Off Than To Be Pissed On" 1989 1.7D DK Box "Dylan" |
|
Sid1800
Groupie Joined: 07 Oct 12 Location: Bradford Status: Offline Points: 70 |
Post Options
Thanks(0)
|
hi nothing is impossible to do the upright conversion,if i can do the 1.8t upright whats so hard about the
diesel upright.using the same engine mounting support bar for the petrol and diesel is the same. hitting 88 miles per hour dont know what you mean i have had the van at 120 mph with a s3 engine on standard box in the same van.
|
|
S-Line Motors-Photobucket
German Vehicle Specialist 07971728333 |
|
rowlesy
Vanorak murdered the murderwagen Joined: 09 Oct 05 Location: up unit! Status: Offline Points: 6466 |
Post Options
Thanks(0)
|
thats his signature! on every one of his posts!
|
|
UberFukz broke another! sucky sucky five dollah!
always out numbered never out gunned! RWS welding 07846 380 467 (worcs) |
|
rhysdubber
Groupie Joined: 10 Jan 13 Location: South Wales Status: Offline Points: 41 |
Post Options
Thanks(0)
|
Ive only ever reached 87/88 mph in my 1.7D Thats outright dangerous to the public Very nerving... and loud. We done a 118 in my Dad's 2.1 Auto. That was much more enjoyable (Not shitting myself) haha Ive had a look at your 1.8T conversion thread. Very well done, its made me want to petrol instead of diesel now
|
|
If my calculations are correct, when this baby hits eighty-eight miles per hour... you're gonna see some serious shit.
"Better To Be Pissed Off Than To Be Pissed On" 1989 1.7D DK Box "Dylan" |
|
spuds_own
Not Quite Newbie Joined: 10 Jul 11 Location: Doncaster Status: Offline Points: 16 |
Post Options
Thanks(0)
|
Cracking job mate ive just started my 20vt build which direction did you go for the gearbox flip adapter plate or machine off and reweld?
|
|
Sid1800
Groupie Joined: 07 Oct 12 Location: Bradford Status: Offline Points: 70 |
Post Options
Thanks(0)
|
hi spuds
sorry just been a busy person from work and home. any way the gearbox was cut on the face by 15mm all round due to the adaptor plate being 15mm thick.the direction is 180degree flip for the gearbox,no welding involved atall you can buy the adaptor plate from Tim under the user name vw nerd.he supplied me with the parts and i did the build. by the way your not to far from me (bradford)if you want to have a look at mine by all means if you make it during this week i can also show you a t3 with a 3.3 subaru that i did a while back.customer collecting it next week end.
Edited by Sid1800 - 22 Feb 13 at 17:46 |
|
S-Line Motors-Photobucket
German Vehicle Specialist 07971728333 |
|
spuds_own
Not Quite Newbie Joined: 10 Jul 11 Location: Doncaster Status: Offline Points: 16 |
Post Options
Thanks(0)
|
Hey sid that would be cool can you pm me your number and I'll give you a call about coming up
|
|
Post Reply | Page <12345 8> |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |