1z flywheel timing mark |
Post Reply |
Author | |
rolo
Yardie Joined: 17 Oct 08 Location: burnley Status: Offline Points: 519 |
Post Options
Thanks(0)
Posted: 05 Jan 12 at 19:43 |
done a search, no luck, must be using the wrong words.
putting a 1z flywheel on the panel van, does the original tdi timing mk line up with the diesel bell housing window pointer or do I need to make one? cheers rolo.
|
|
the last one
|
|
langb20
Groupie Joined: 28 Jul 09 Location: Pembrokeshire Status: Offline Points: 145 |
Post Options
Thanks(0)
|
nope you need to make a new one, when viewing thru the bellhousing i think the notch is actually on the clutch plate but it definitely lines up differently to the JX flywheel
|
|
'82 1Z camper project
|
|
langb20
Groupie Joined: 28 Jul 09 Location: Pembrokeshire Status: Offline Points: 145 |
Post Options
Thanks(0)
|
excerpt from where I read that before:
The problem with making a new mark is in the case of installing 1Z/AHU motor at 50 deg, using a diesel bellhousing that has the hole/window in a different location. So, in order to make sure pison 1 /flywheel is at Top Dead Center, you need to remark the flywheel so the pointer that is in that (diesel bellhousing)hole/window/opening.. will align with the mark on flywheel. And there is on offset of 225mm ccw if I remmember correctly, where you have to make a new mark that will corespond to the new location on that bellhousing. http:////autos.groups.yahoo.com/group/TDI-conversion/message/10277 hope that helps |
|
'82 1Z camper project
|
|
..lee..
Vanorak Joined: 14 May 08 Location: llanelli swales Status: Offline Points: 1420 |
Post Options
Thanks(0)
|
there`s a tdc marker on the front pulley and belt cover. no real need to mess around with the flywheel its a pain in the arse to see anyway.
lee. |
|
it`s a big round cage but there`s too many animals in it for my liking.to address this ring lee on 07977 765818.
|
|
max and caddy
Vanorak Joined: 12 Dec 09 Location: Lancaster..uk Status: Offline Points: 4866 |
Post Options
Thanks(0)
|
front pulley is not very accurate tho...quite a bit of wobble in it when bolts are loose
|
|
syncroandy
Yardie Joined: 18 May 05 Location: North Lancs. UK Status: Offline Points: 630 |
Post Options
Thanks(0)
|
Just done this job on the engine I'm working on at the mo. Agree with Alex you want to set TDC off the FW to get it bob on. I first used the VW 2068A tool to position the FW (set to 96mm). Then popped a spare BH on and marked the pressure plate, then made a shallow groove with a dremel to hold some paint. I just measured the new mark using a bit of wire round the circumference of the FW, it is indeed 225mm anticlockwise from the original mark.
Edited by syncroandy - 06 Jan 12 at 13:43 |
|
rolo
Yardie Joined: 17 Oct 08 Location: burnley Status: Offline Points: 519 |
Post Options
Thanks(0)
|
excellent work from the knowledge, thanks just the answer i wanted.
Edited by rolo - 06 Jan 12 at 21:06 |
|
the last one
|
|
mazz
Yardie Joined: 04 Mar 07 Location: shropshire Status: Offline Points: 584 |
Post Options
Thanks(0)
|
I have found another way of marking up TDC mark too, you need to set up TDC first using 1Z flywheel nd gearbox, we have cut a section off a TDi gearbox to mke life easy for us, you can then remove crank sensor and mark sensor ring itself. makes for a accurate way of finding TDC, and is very easy to view.
|
|
MV Engineering-TDi conversion specialist
07989593569-01952 581818 mveservices@hotmail.co.uk |
|
rotaecho
Newbie Joined: 23 Sep 16 Location: Los Angeles, CA Status: Offline Points: 2 |
Post Options
Thanks(0)
|
Howdy! I'm trying to find TDC on an 82' Vanagon Diesel AHU mTDI conversion soon.
I was trying to mark the LUK 17-050 Flywheel using the CCW 225mm from the TDI TDC Flywheel mark. However, it is unclear to me which orientation on the unit to mark 225mm CCW. Would it be from the Flywheel Side of: Or If it would be on the Clutch Side to do the CCW of 225mm Thanks! Edited by rotaecho - 23 Sep 16 at 04:57 |
|
-Will
http://www.vanagondiesel.info |
|
rotaecho
Newbie Joined: 23 Sep 16 Location: Los Angeles, CA Status: Offline Points: 2 |
Post Options
Thanks(0)
|
Looks like going 225mm CCW from the second photo (Pressure Plate / Clutch facing you) would be correct.
|
|
-Will
http://www.vanagondiesel.info |
|
Post Reply | |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |