VAG COM adaption for locking options |
Post Reply | Page 12> |
Author | |
stalbansdragon
Groupie Joined: 02 Mar 10 Status: Offline Points: 63 |
Post Options
Thanks(0)
Posted: 01 Mar 11 at 11:37 |
Hi,
Does anybody know the VAG COM control module and adaption codes relating to central locking? In particular I want to enable:
1) Auto lock above 10 mph
2) Single click for passenger and sliding door
3) bleep on lock
Thanks if anyone can help with any of these
|
|
T5 TDI
Vanorak Joined: 05 Nov 05 Status: Offline Points: 3687 |
Post Options
Thanks(0)
|
1 & 3 are easy. It's hard to go wrong. You need to go to 'cent conv' followed by 'adaption'. Then scroll up to ch 3 and change the zero to a 1. Go to ch 4 if you want the the auto unlock option which unlocks the doors again when you take the key out. The beep on locking/unlocking is similar, just choose the relevent channel. You can make the hazards flash on locking/unlocking also.
If you have a genuine and up to date version of VCDS you will get a bubble pop up which leads you by the nose for everything.
The selective locking option (one press locks all or only driver's door) is slightly different. For that you need to go to 'cent conv' again but choose 'coding' rather than ''adaption'. Make a careful note of the original coding shown. Using this you can put it back exactly as it was before if you mess it up. Follow the instructions for the various options for the locks and other things on the screen.
Come back if you have any problems. Edited by T5 TDI - 01 Mar 11 at 19:43 |
|
2004 2.5 174
|
|
BANANABUS
Vanorak More Like BanBus! Joined: 01 Jul 07 Location: W YORKS Status: Offline Points: 1987 |
Post Options
Thanks(0)
|
Is it possible to turn off the beep on the electric side doors when they are closing on the velle? It annoys the he'll out of me .
|
|
Committed To Famine Relief. Last Week I Sucked Off An Ethiopian
I'm Not Arguing,I'm Explaining Why I Am Right |
|
T5 TDI
Vanorak Joined: 05 Nov 05 Status: Offline Points: 3687 |
Post Options
Thanks(0)
|
Never had much to do with the electric doors, really only what I've read around the net. But most beeps can be switched off via VCDS. I'll check it out.
|
|
2004 2.5 174
|
|
PeteO
Not Quite Newbie Joined: 30 Jan 11 Location: Midlands Status: Offline Points: 29 |
Post Options
Thanks(0)
|
I have VCDS lite, will I still be able to adjust what you suggest?
Cheers |
|
T5 TDI
Vanorak Joined: 05 Nov 05 Status: Offline Points: 3687 |
Post Options
Thanks(0)
|
I couldn't find anything about turning off that beep. If I come across anything I'll let you know.
PeteO- VCDS lite won't be able to adjust anything. You need a genuine cable with a dongle and full software. (Free when you buy the cable).
|
|
2004 2.5 174
|
|
T5 TDI
Vanorak Joined: 05 Nov 05 Status: Offline Points: 3687 |
Post Options
Thanks(0)
|
There are a few other things re the electric doors you can alter. You can change which button opens or closes it. Exiting eh? And there are some basic settings via diagnostics needed if you fit new parts. Pete- VCDS lite is the shareware version of VCDS. Available free for anyone to use even with a flebay cable. It's quite limited but it will read codes, and will sometimes work for other things depending on the car. It can't do any adaptions.On the VCDS website it says it won't work on can-bus equipped vehicles which should make it useless on all T5's but since the can-bus system seems limited on early T5's maybe it will do some things. Have you been able to connect to any controllers on yours?
|
|
2004 2.5 174
|
|
PeteO
Not Quite Newbie Joined: 30 Jan 11 Location: Midlands Status: Offline Points: 29 |
Post Options
Thanks(0)
|
I got on to all the things you said in the earlier post, but when I went to alter them it said I needed to register the software. So I have done, just waiting for Ross tech to get back to me with my activation code. Then I will let you know how I get on!!
|
|
PeteO
Not Quite Newbie Joined: 30 Jan 11 Location: Midlands Status: Offline Points: 29 |
Post Options
Thanks(0)
|
Worked a treat, set it to auto lock and auto unlock!!!!! very very easy!!!
Cheers T5 TDI!!! How do you reset the service info when that comes up? |
|
blackvanman
Vanorak Joined: 03 May 09 Location: North Wales Status: Offline Points: 1218 |
Post Options
Thanks(0)
|
I've got 10.6 software with my ross tech lead and i don't get bubbles leading me by the nose!! what are you taking T5TDI as your'e using it or is it special glasses?!
|
|
'09' 174 kombi, swb, pearl black
|
|
energysolutions
Vanorak Joined: 02 Dec 08 Location: Earth (For Now) Status: Offline Points: 3684 |
Post Options
Thanks(0)
|
I too have the latest version VCDS and I get the advice bubbles that T5 TDI speaks of........
|
|
!!Never Eat Yellow Snow!!
|
|
T5 TDI
Vanorak Joined: 05 Nov 05 Status: Offline Points: 3687 |
Post Options
Thanks(0)
|
You should get the bubbles on your late software. I think it's a 'hover over' thing try scrolling around a bit more maybe?
|
|
2004 2.5 174
|
|
T5 TDI
Vanorak Joined: 05 Nov 05 Status: Offline Points: 3687 |
Post Options
Thanks(0)
|
Go to 'instruments' followed by 'adaptions'. Then scroll up to ch 2 and change the existing figure (probably a 1 or a 2) to a zero. Then click 'test' first then 'do it' or similar.
That resets the longlife service regime. There is a one click option for the reset on later VCDS versions but never tried it.
Edited by T5 TDI - 04 Mar 11 at 07:14 |
|
2004 2.5 174
|
|
stalbansdragon
Groupie Joined: 02 Mar 10 Status: Offline Points: 63 |
Post Options
Thanks(0)
|
Thanks for taking the time to give a detailed reply...but it doesn't work for me. I can never connect to Central Conv. (46) - I just get no response from controller. I'd read it had been replaced with Central elect (09) which I can connect to. When I connect to 09 the component is BORDNETZ SGVER. However channel 3 has a value of 254 (so neither 0 or 1) and channel 4 is set at 15. |
|
PeteO
Not Quite Newbie Joined: 30 Jan 11 Location: Midlands Status: Offline Points: 29 |
Post Options
Thanks(0)
|
When i go to the selective locking option (one press locks all or only driver's door) For that I go to 'cent conv'
but choose 'coding' rather than ''adaption'.
Here mine says Software coding 00021 and workshop 02736. what do I change it to to get one press drivers door lock/unlock etc??? Did not want to mess to much as it gives a scary message about really screwing stuff up etc!!!!!! Sorry being so thick! |
|
T5 TDI
Vanorak Joined: 05 Nov 05 Status: Offline Points: 3687 |
Post Options
Thanks(0)
|
No problems, it's complicated! I'm still learning and at 53 I don't think my poor old brain is up to it any more.
I just confirmed it on my van, (and it's bloody ffreezing out there!) you need to to add a 1 to your van's software coding (not all vans are the same) to change it to 00022 and that should do it. You can always put it back. Ignore the workshop code that's for something else. You are fine with this coding change and it is fun playing with the possible adaptions (listed in the bubble on VDCS) in the instruments controller too but don't alter anything especially in the engine controller unless you are sure about what you are doing.
Edited by T5 TDI - 04 Mar 11 at 22:02 |
|
2004 2.5 174
|
|
T5 TDI
Vanorak Joined: 05 Nov 05 Status: Offline Points: 3687 |
Post Options
Thanks(0)
|
You should be able to connect with cent conv (46) ok. I don't think it has been 'replaced' by cent elec (09). That's a separate controller. If yours isn't a genuine cable maybe that is the problem because they don't work properly for some things.
The channels I mentioned are specific to the cent conv controller, if you change the numbers in those same channels but in a different controller you could come unstuck. Edited by T5 TDI - 04 Mar 11 at 21:38 |
|
2004 2.5 174
|
|
PeteO
Not Quite Newbie Joined: 30 Jan 11 Location: Midlands Status: Offline Points: 29 |
Post Options
Thanks(0)
|
T5 yet again your are a diamond!!!!!!! top of the class! cheers mate!
|
|
PeteO
Not Quite Newbie Joined: 30 Jan 11 Location: Midlands Status: Offline Points: 29 |
Post Options
Thanks(0)
|
I can connect to my 08 T5 with my VCDS but not to my mates T5gp 2010? I thought it was the same system for all? or is id different for the newer model?
|
|
T5 TDI
Vanorak Joined: 05 Nov 05 Status: Offline Points: 3687 |
Post Options
Thanks(0)
|
Never tried connecting to a T5.1 but I'm pretty sure there should be no problem. Have you updated your software from VDCS lite (it's free now you have registered) because VDCS lite won't work on the full can-bus van that the T5.1 must be. |
|
2004 2.5 174
|
|
Post Reply | Page 12> |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |