corrado mirrors are on.... |
Post Reply | Page 12> |
Author | ||
STEW '89GL
Groupie Joined: 23 Aug 07 Status: Offline Points: 201 |
Post Options
Thanks(0)
Posted: 02 Feb 08 at 01:45 |
|
Managed to get a switch from a corrado aswell, but they are the same as passats, mk 2 golfs and I have reason to believe the same as T3's. If their not they soon will be, I think I still have the manual from my old passat in the garage somewhere, I'll try and locate it and get back to you if successful. |
||
The voices made me do it.............
|
||
crewie
Yardie Joined: 28 May 07 Location: esssex init Status: Offline Points: 406 |
Post Options
Thanks(0)
|
|
Dude.....
we have been so busy at work ive not even painted them yet ,im still driving round with blue mirrors . i need to rob a mirror switch out of something as well. if you manage to find a wiring diagram or work out what does what let me know. |
||
|
||
STEW '89GL
Groupie Joined: 23 Aug 07 Status: Offline Points: 201 |
Post Options
Thanks(0)
|
|
Mirrors have arrived and ready to go. Any joy with wiring yours up yet Crewie? |
||
The voices made me do it.............
|
||
STEW '89GL
Groupie Joined: 23 Aug 07 Status: Offline Points: 201 |
Post Options
Thanks(0)
|
|
There are still bargains to be had on evil bay!
|
||
The voices made me do it.............
|
||
crewie
Yardie Joined: 28 May 07 Location: esssex init Status: Offline Points: 406 |
Post Options
Thanks(0)
|
|
£6.50
thats nearly free |
||
|
||
STEW '89GL
Groupie Joined: 23 Aug 07 Status: Offline Points: 201 |
Post Options
Thanks(0)
|
|
A pair have been purchased for the extortionate sum of £21.50! That includes the £15 recorded delivery. £6.50 for a pair of mirrors |
||
The voices made me do it.............
|
||
crewie
Yardie Joined: 28 May 07 Location: esssex init Status: Offline Points: 406 |
Post Options
Thanks(0)
|
|
not yet, but it cant be that hard to do,just need to find a corrado wiring diagram.
|
||
|
||
Daveangel9
Groupie Joined: 05 Apr 07 Location: United Kingdom Status: Offline Points: 125 |
Post Options
Thanks(0)
|
|
Have you got these wired up? if so was it an easy job?
|
||
1990 slate Blue twin slider 2.1 Nearly finished not to everyones taste
|
||
VWlewis
Yardie Joined: 03 Oct 06 Location: East Midlands Status: Offline Points: 740 |
Post Options
Thanks(0)
|
|
The way to sort out the manual mirrors is to take the tightener nut off, pull apart the arm and use some sandpaper and roughen the surface that rub together when they move - then clean with a solvent to remove any grease - reassemble and tighten .. works a treat - did that to mine which has not moved since.
Hope this helps. VW Lewis |
||
|
||
STEW '89GL
Groupie Joined: 23 Aug 07 Status: Offline Points: 201 |
Post Options
Thanks(0)
|
|
Whatever you can see out of them is going to be more than I can see now with the poxy things keep folding in. No matter how many times I've had them off to tighten them up, after a week or so they fold in and face each other, even locktited them and managed two weeks, great! Also there's the problem of adjusting the passenger one on your own, not that I'm a lazy bastard or anything, but leccys got to be the way foward. |
||
The voices made me do it.............
|
||
crewie
Yardie Joined: 28 May 07 Location: esssex init Status: Offline Points: 406 |
Post Options
Thanks(0)
|
|
i was gonna say that but thought stew might think i was takin the pi$$ |
||
|
||
STEW '89GL
Groupie Joined: 23 Aug 07 Status: Offline Points: 201 |
Post Options
Thanks(0)
|
|
Cheers, another purchase coming up! |
||
The voices made me do it.............
|
||
shapey
Vanorak Joined: 09 Oct 06 Location: loughborough Status: Offline Points: 3194 |
Post Options
Thanks(0)
|
|
what, like a corrado for example? |
||
crewie
Yardie Joined: 28 May 07 Location: esssex init Status: Offline Points: 406 |
Post Options
Thanks(0)
|
|
hi stew.
vision out of them is surprisingly good ,obviously you cant see the full height of the van but otherwise no problems. id say you get about the same field of view as a saloon car. |
||
|
||
STEW '89GL
Groupie Joined: 23 Aug 07 Status: Offline Points: 201 |
Post Options
Thanks(0)
|
|
Hi, being smaller than standard mirrors, what sort of vision do you get with the corrado mirrors?
|
||
The voices made me do it.............
|
||
crewie
Yardie Joined: 28 May 07 Location: esssex init Status: Offline Points: 406 |
Post Options
Thanks(0)
|
|
Ok then here goes.
make sure when you get the mirrors ,you get the base gaskets and the mounting screws as well.the rado screws are longer and it makes life a whole lot easier to get everything lined up. first thing to do is to remove the standard mirrors ,two philps screws each side ,stick them in the for sale section,somebody might need them. next job is to remove the interior door fittings and pop off the door pads. if you still have the plastic membrane intact ,locate the opening in the door frame directly under the quarter light and cut a hole big enough for your hand in the membrane ,this should be resealed when your done.i use a piece of polythene fixed with double sided tape but you can use duck tape. on to the corrado mirrors themselves. if you look at the base of the mirror ,the screw mounting holes have a raised area that locates in a dimple on the corrado door ,this needs to be ground down flush with the base of the mirror.its only ally so grinds down farliy quickly on a bench grinder. as peet said the corrado screw mountings are at a 15 degree angle ,so using a 6mm drill bit ,drill down through the mounting hole from the side you just ground and straighten them up as much as possible without making them oversized .i offered them up to the door several times before i was happy they were straight enough.dont make the holes too big or the screw may just pull through when you tighten them. cut the plugs from the bottom of the wiring ,leave enough wire to rejoin them if you plan on wiring them up in the future. use a craft knife or razor blade to cut the dimples from the mirror base gasket. spin the mirror base to get access to the front mounting hole and offer it up the the van with the gasket.feed the wiring down through the center hole and using the corrado screws attach it to the door ,front hole to front hole.be carefull as its easy to cross thread the screw if the hole isnt straight enough . when its tightened down, spin the mirror the other way to access the rear hole .a bit of masking tape stuck to the door before attaching the mirror is the best way of mark where to drill.when your sure the mirror is square on the door mark the hole. remove the mirror and using your 6mm drill, carefully whack a hole though your door .if your lucky, you will just drill through the edge of the mirror mounting plate underneath ,this is a good thing. remove the masking tape ,debur the hole ,touch in the edge with paint and allow to dry.you can seal up the original rear hole with a blob of sealer if your worried about water getting in to the door refit the mirror to the door, front hole first and then screw in the rear one .grab a 10mm nut and washer ,stick your hand through the hole in the membrane and wind it onto the rear screw.it can be a bit fiddly doing it up but with the help of an assistant turning the screw from outside, you just need to hold a spanner on it. thats about it i think . reseal the membrane ,refit the door pads and fittings ,sit in the drivers seat and adjust the glass to your preference and stand outside with a big cheesy grin on your face coz yer van looks cool. it really is a pi$$ easy job that makes a big difference i think. a pair of rado mirrors can be had for around £20 and you could get a tenner or more for your old ones .if you dont want to mess about or spend the money getting them painted body colour ,just satin black them. most of this info i got from one of peets previous posts i think,so thanks to him. cheers matey dazz |
||
|
||
mister t
Groupie Joined: 14 Dec 06 Location: United Kingdom Status: Offline Points: 200 |
Post Options
Thanks(0)
|
|
I just cheated and used one hole for now to allow the quarter light to open, I'll work out what I'm gonna do some day , only been 18 months |
||
Ain't goin on no plane FOOL!
Bristol V-Dub Misfitz |
||
andycaddock
Yardie Joined: 03 Nov 07 Location: United Kingdom Status: Offline Points: 573 |
Post Options
Thanks(0)
|
|
a step by step would be great
|
||
peet
Vanorak Soft Southern Shite Joined: 03 Jan 06 Location: Crawley Status: Offline Points: 3319 |
Post Options
Thanks(0)
|
|
I just reground and trial fitted to get the angle. U could jus redrill the holes to allow the quarter to open and bring it back which would look ok but then u have other holes to fill! |
||
Firefighter twisted Firefighter...
|
||
shapey
Vanorak Joined: 09 Oct 06 Location: loughborough Status: Offline Points: 3194 |
Post Options
Thanks(0)
|
|
yeah, a fitting guide would be very useful, ta! would it not be possible to make a wedge shaped shim to angle the mirrors up a bit? or would that bring the body of the mirror into contact with the window? i really like the look but i also really like to drive with the quarter light open |
||
Post Reply | Page 12> |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |